#

Lathe Machine

Technical Specification of Lathe Machine
Standards  
Lathe Machine Confirming to IS 6893-1988 Latest (For Technical Evaluation) Yes
Lathe Machine Material Confirming to IS 210 Latest(For Casting ) Yes
Lubrication System Requirement as per IS:11118 Yes
Cooling System Requirement as per IS :11118 Yes
Positioning Accuracy as per IS:1878 latest for Cumulative Error Yes
Positioning Accuracy as per IS:1878 latest for Repeatibility Yes
Positioning Accuracy as per IS:1878 latest for Backlash Yes
Positioning Accuracy as per IS:1878 latest for Minimum Possible Requirement Yes
Geometric Accuracy as per IS 1878-1971 latest for general purpose lathe Yes
Geometric Accuracy as per IS 6040-1972 latest for precision lathe Yes
Machine Bed & Tail Stock casting Grade as per IS 11118-1997 latest Yes
Tail stock sleeve case hardening steel 15Ni7Cr4M02 as per IS 1118-1997 latest Yes
Head Stock Drive gears Conformity confirming to Alloy steel material specification 15 Ni 7 Cr 4 M02 , hardened 58-62 HRC and profile ground with 0.8 micron surface roughness Ra value
Main Spindle Conformity confirming to C2R grade forged Steel and hardened 58-62 HRC. / ground with 0.8 micron surface roughness Ra value
Performance Parameters  
Manually Operated Lathe Yes
Geared Mechanism Yes
Lathe Machine Type Center Lathe
Nature of Duty of Operation of Lathe Light Duty Lathe
Distance Between centers (mm) x Swing over Bed (mm) 1000 x 300
Swing Over Bed (in mm) 300 millimeter
Center Height in mm 150 millimeter
Swing Over Cross Slide in mm 170 millimeter
Swing Over Carriage Wing in mm 150 millimeter
Swing in Gap in mm 500 millimeter
Width of Gap in Front in mm 100 millimeter
Type of Bed Inverted V type
Length of Bed in mm 1800 millimeter
Width of Bed in mm 240 millimeter
Gap in Bed in mm ( Only for Gap Lathe ) for rest Put 0 0 millimeter
Rapid Transverse of saddle & Cross Slide No
Maximum Feed Force 5
Maximum Facing Diameter in mm 300 millimeter
Maximum Weight of work piece that can be held between chuck and supported by Live center in kg 35 kilogram
Maximum Weight of work piece that can be held between chuck and supported by dead center in kg 50 kilogram
Maximum Torque on Spindle in NM 5
Type of Spindle THREADED
Size of Spindle in mm 62 millimeter
Type of Spindle Nose THREADED
Taper in Spindle Bore as per IS 2582-1972 with Latest amndmt MT - 5
Taper Bore in Spindle Sleeve as per IS 1715-1986 with Latest amndmt MT - 3
Bore in Spindle in mm 40 millimeter
Range of Spindle Speed in Forward Direction in rev/min 8
Range of Spindle Speed in Reverse Direction in rev/min 8
Type of Chuck 3 Jaw Self Centered
Travel of Cross Slide in mm 170 millimeter
Travel of Top Slide in mm 100 millimeter
Type of Tool Holder SQUARE
Tool Shank Size as per IS 1983:1958 latest in mm x mm 16 X 16
Main Motor Power in kw 5.5 kiloWatt
Rapid Traverse Motor Power in kw 0 kiloWatt
Type of Cooling AIR COOLED
speed of coolant motor in rev/min 2800
Noise emitted by Machine in db as per IS 10998:1984 latest 85
Mechanical Guarding as per IS 9474 :1980 latest Yes
In possession of Technical Evaluation report as per IS :11118 Yes
Main Spindle Bearing confirming Pre-loaded of Standard make Yes
Confirming of machine towards dynamically balanced spindle and other parts No
Spindle Forward/Reverse Drive transmission through Electro Magnetic Double Clutch No
Spindle Forward/Reverse Drive transmission through Hydraulic Friction Clutch No
Types of power supply 3 Phase
Erection and Commisioning Charges included in Offered Prices without Foundation Yes
Warranty in Years 1
Annual Maintenance Contract Rate included for Machine No
Period of AMC 0
Coolant Pump output in kw as per IS 2161:1962 Latest 0.12
Coolant Pump Discharge at maximum working height as per IS 2161:1962 with latest amndmt in l/min 10
Dimensional Parameters  
Minimum Chucking Diameter in mm 10 millimeter
Maximum Chucking Diameter in mm 200 millimeter
Tail Stock Sleeve Diameter in mm 38.1 millimeter
Tail Stock Spindle Taper as per IS 1715:1986 with latest MT - 3
Maximum Offset of Tailstock on either side of Center Line in mm 5 millimeter
Sleeve Travel Type(Tail Stock) Manual
Travel of Sleeve in mm 120 millimeter
Hardness of Bed Guide Ways in HRC 42
Lead Screw Diameter in mm 25.8 millimeter
Lead Screw Pitch in mm 6.35
Longitudinal Lead Screw Feed Range in mm/rev STANDARD
Cross feed Range in mm/rev STANDARD
Metric Thread Range in mm STANDARD
British Thread Range in TPI STANDARD
Module Thread Range in mm 0
Diameteral Pitch Range in mm 0
Type of Lubrication MANUAL
Length of Lathe Machine in mm 2100 millimeter
Width of Lathe Machine in mm 750 millimeter
Height of Lathe Machine in mm 1100 millimeter
Weight of Lathe Machine with electrical and standards Accessories 700 kilogram
Colour of Lathe machine as per IS 5 :1978 with latest amndmt APPLE GREEN
Machine Confirming Full power cutting load test to full length Turning capacity of Machine Yes
Availability of Drawing for Foundation Yes
Lead screw Ground profile& Pitch accuracy 0.03 mm over a length of 300 mm
Standard Accessories  
Driving Plate With Peg Yes
Coolant Equipment & swarf tray Yes
Splash Guard Yes
Spindle Reduction Sleeve Yes
60 Deg Dead Centre-2 Nos Yes
Quick change tool post with Tool Holders Yes
Quick indexible Square tool post Yes
A Set of Operating Instructions Manual & a set of operating tools Yes
Optional Accessories  
3 Jaw Self Centering Chuck Yes
Precision 3 jaw Self Centering Chuck( Hydraulic /Pneumatic complete Chuck ) No
Chuck Guard No
Rear Tool Post No
Universal face plate No
Precision Face Plate No
Cast iron Face Plate No
Collet Chuck & Collets No
Rear Tool Holder No
Steady Rest No
Roller Steady Rest No
Follow Rest No
Longitudinal Stop No
Roller Stop No
Taper Turning Attachment No
A Set of Change Gear For DP Threads No
Multi Copying Attachment No
Machine Lamp No
Swraf Tray Complete with coolant equipment No
Four Jaw Chuck Yes
Additional Specification Parameter  
Specification Parameter Names Bid Requirement (Allowed Values)
Following accessories should be supplied along with the machine: 1. Half Centre 2. Pipe Centre 1. Half Centre suitable to the machine, Qty.: 02 Nos. 2. Pipe Centre suitable to the machine, Qty: 02 Nos.
3. Revolving Centre 4. Cross Knurling Tool 3. Revolving Centre suitable to the machine, Qty.: 02 Nos. 4. Cross Knurling Tool suitable to the machine: Fine, Rough and Medium types, Qty.: 02 Nos. each
5. 4 Jaw Chuck 5. 4 Jaw Chuck suitable to the machine, Qty.: 01 No.