Lathe Machine Confirming to IS 6893-1988 Latest (For Technical Evaluation) |
Yes |
Lathe Machine Material Confirming to IS 210 Latest(For Casting ) |
Yes |
Lubrication System Requirement as per IS:11118 |
Yes |
Cooling System Requirement as per IS :11118 |
Yes |
Positioning Accuracy as per IS:1878 latest for Cumulative Error |
Yes |
Positioning Accuracy as per IS:1878 latest for Repeatability |
Yes |
Positioning Accuracy as per IS:1878 latest for Backlash |
Yes |
Positioning Accuracy as per IS:1878 latest for Minimum Possible Requirement |
Yes |
Geometric Accuracy as per IS 1878-1971 latest for general purpose lathe |
Yes |
Geometric Accuracy as per IS 6040-1972 latest for precision lathe |
Yes |
Machine Bed & Tail Stock casting Grade as per IS 11118- 1997 latest |
Yes |
Tail stock sleeve case hardening steel 15Ni7Cr4M02 as per IS 1118-1997 latest |
Yes |
Head Stock Drive gears Conformity |
confirming to Alloy steel material specification 15 Ni 7 Cr 4 M02 , hardened 58-62 HRC and profile ground with 0.8 micron surface roughness Ra value |
Main Spindle Conformity |
confirming to C2R grade forged Steel and hardened 58-62 HRC. / ground with 0.8 micron surface roughness Ra value |
Manually Operated Lathe |
Yes |
Geared Mechanism |
Yes |
Lathe Machine Type |
Center Lathe |
Nature of Duty of Operation of Lathe |
High Speed Precision Lathe |
Distance Between centers (mm) x Swing over Bed (mm) |
1000 x 400 |
Swing Over Bed (in mm) |
420 |
Center Height in mm |
200 |
Swing Over Cross Slide in mm |
220 |
Swing Over Carriage Wing in mm |
400 |
Swing in Gap in mm |
0 |
Width of Gap in Front in mm |
0 |
Type of Bed |
Inverted V type |
Length of Bed in mm |
1950 |
Width of Bed in mm |
289 |
Gap in Bed in mm ( Only for Gap Lathe ) for rest Put 0 |
0 |
Rapid Transverse of saddle & Cross Slide |
No |
Maximum Feed Force |
1030 |
Maximum Facing Diameter in mm |
430 |
Maximum Weight of work piece that can be held between chuck and supported by Live center in kg |
150 |
Maximum Weight of work piece that can be held between chuck and supported by dead center in kg |
350 |
Maximum Torque on Spindle in NM |
280 |
Type of Spindle |
METRIC 50 |
Size of Spindle in mm |
133 |
Type of Spindle Nose |
A2-5 INCHES |
Taper in Spindle Bore as per IS 2582-1972 with Latest amndmt |
METRIC 50 |
Taper Bore in Spindle Sleeve as per IS 1715-1986 with Latest amndmt |
MT-4 |
Bore in Spindle in mm |
42 |
Range of Spindle Speed in Forward Direction in rev/min |
60 TO 1500 |
Range of Spindle Speed in Reverse Direction in rev/min |
60 TO 1500 |
Type of Chuck |
3 Jaw Self Centered |
Travel of Cross Slide in mm |
215 |
Travel of Top Slide in mm |
105 |
Type of Tool Holder |
SQUARE SHANK |
Tool Shank Size as per IS 1983:1958 latest in mm x mm |
25x25 |
Main Motor Power in kw |
3 |
Rapid Traverse Motor Power in kw |
0 |
Type of Cooling |
NATURAL AIR COOLING |
speed of coolant motor in rev/min |
2800 |
Noise emitted by Machine in db as per IS 10998:1984 latest |
85 |
Mechanical Guarding as per IS 9474 :1980 latest |
Yes |
In possession of Technical Evaluation report as per IS |
Yes |
:11118 |
Main Spindle Bearing confirming Pre-loaded of Standard make |
Yes |
Confirming of machine towards dynamically balanced spindle and other parts |
Yes |
Spindle Forward/Reverse Drive transmission through Electro Magnetic Double Clutch |
No |
Spindle Forward/Reverse Drive transmission through Hydraulic Friction Clutch |
No |
Types of power supply |
3 Phase |
Erection and Commissioning Charges included in Offered Prices without Foundation |
Yes |
Warranty in Years |
1 |
Annual Maintenance Contract Rate included for Machine |
No |
Period of AMC |
0 |
Coolant Pump output in kw as per IS 2161:1962 Latest |
0.12 |
Coolant Pump Discharge at maximum working height as per IS 2161:1962 with latest amndmt in l/min |
30 |
Minimum Chucking Diameter in mm |
10 |
Maximum Chucking Diameter in mm |
400 |
Tail Stock Sleeve Diameter in mm |
70 |
Tail Stock Spindle Taper as per IS 1715:1986 with latest |
MT-4 |
Maximum Offset of Tailstock on either side of Center Line in mm |
5 |
Sleeve Travel Type(Tail Stock) |
Manual |
Travel of Sleeve in mm |
140 |
Hardness of Bed Guide Ways in HRC |
52 |
Lead Screw Diameter in mm |
36 |
Lead Screw Pitch in mm |
6 |
Longitudinal Lead Screw Feed Range in mm/rev |
0.05 TO 2.8 |
Cross feed Range in mm/rev |
0.01 TO 0.62 |
Metric Thread Range in mm |
0.5-14 |
British Thread Range in TPI |
2 TO 56 |
Module Thread Range in mm |
0 |
Diameteral Pitch Range in mm |
0 |
Type of Lubrication |
DRY SUMP LUBRICATION |
Length of Lathe Machine in mm |
2300 |
Width of Lathe Machine in mm |
1100 |
Height of Lathe Machine in mm |
1135 |
Weight of Lathe Machine with electrical and standards Accessories |
1300 |
Colour of Lathe machine as per IS 5 :1978 with latest amndmt |
Apple Green |
Machine Confirming Full power cutting load test to full length Turning capacity of Machine |
Yes |
Availability of Drawing for Foundation |
Yes |
Lead screw |
Ground profile& Pitch accuracy 0.03 mm over a length of 300 mm |
Driving Plate With Peg |
Yes |
Coolant Equipment & swarf tray |
Yes |
Splash Guard |
Yes |
Spindle Reduction Sleeve |
Yes |
60 Deg Dead Centre-2 Nos |
Yes |
Quick change tool post with Tool Holders |
Yes |
Quick indexible Square tool post |
Yes |
A Set of Operating Instructions Manual & a set of operating tools |
Yes |
3 Jaw Self Centering Chuck |
Yes |
Chuck Guard |
Yes |
Precision Face Plate |
Yes |
Steady Rest |
Yes |
Follow Rest |
Yes |
Taper Turning Attachment |
Yes |
Machine Lamp |
Yes |
Four Jaw Chuck |
Yes |